YX250GY-C6D
173FMM
LB425Y6D
| 一、specification | ||||
| English item | specification | |||
| Overall dimension (length × wide × Height) mm | 2070×830×1165mm | |||
| Wheelbase mm | 1310 | |||
| Minimum ground clearance mm | 300 | |||
| Seat cushion height mm | 890 | |||
| Operating handle return angle (left/right) | ≤42° | |||
| Minimum turning radius mm | 2200 | |||
| Final transmission ratio | 13:45 | |||
| Climbing slope | ≥34° | |||
| Seats | 1 | |||
| Shift mode | Five-gear international | |||
| Fuel tank volume L | 9.5 | |||
| Fuel type | 93# | |||
| Rated maximum load kg | 75 | |||
| Net weight kg | 118 | |||
| Curb weight Kg | 126 | |||
| Maximum load total kg | 201 | |||
| Maximum speed Km/h | 110 | |||
| Braking performance m | ≤7m/30km/h | |||
| Starting performance S | ≤15S | |||
| Rated power Kw/r/min | / | |||
| Economic fuel consumption L/100Km | 2.4 | |||
| Brake | front | Disk type | ||
| rear | Disk type | |||
| Brake operation | front | Hand brake | ||
| rear | foot brake | |||
| wheel | Net wheel | |||
| spoke wheel size | front：1.85×21 rear ：2.15×18 | |||
| tyre | Inner and outer tyre | |||
| tyre size | front：90/100-21 rear：110/90-18 | |||
| Tyre pressure (front/rear) Kpa | 280/280 | |||
| Specification and illumination of large bulb | 12V-35W/35W ≥10000cd | |||
| Steering bulb specification | 12V-1W | |||
| Battery specification | 12V7A(all maintenance free)114*68*130 | |||
| 二、 ENGINE SPECIFICATION | ||||
| Engine type | Single cylinder vertical 15°, air cooled, SOHC-2V two valve, built-in balance shaft | |||
| Magneto type | 12V/12 pole/full wave DC | |||
| Stroke mm | 59.6 | |||
| Cylinder diameter mm | 73 | |||
| Working volume of cylinder ml | 249.45 | |||
| Compression ratio | 9.0：1 | |||
| Fuel grade | 93 # gasoline | |||
| Total oil capacity L | 1.5 | |||
| Spark plug model | D8RTC/D8REA | |||
| Spark plug gap mm | 0.6～0.7 | |||
| Valve clearance mm | 0.03±0.05mm | |||
| Starting mode | Electric start/kick start | |||
| Lubricating oil grade | SAE 10W/40 | |||
| Lubrication method | Splash pressure lubrication | |||
| Ignition mode | C.D.I | |||
| Carburetor model | PEn30 | |||
| Carburetor type | Plunger type | |||
| Transmission type | Constant mesh two-stage transmission and five-speed transmission | |||
| Clutch type | Multi-disc oil bath manual clutch | |||
| Primary gear ratio | 2.9166 | |||
| Gearshift ratio | i1=3.000 , i2=2.701. i3=1.529, i4=1.150，i5=0.954 | |||
| Output transmission mode | Chain drive | |||
| Rotation direction of output shaft | Face the output shaft and rotate counterclockwise | |||
| Overall dimension (length × wide × Height) mm | 360×350×430 | |||
| Net mass Kg | 33±0.5 | |||
| Magneto ignition advance angle | 30º | |||
| Rated power and corresponding speed kW (r/min ± 5%) | / | |||
| Maximum net power and corresponding speed kW (r/min ± 5%) | 13.6Kw/8000r/min | |||
| Maximum torque and corresponding speed N.m (r/min ± 5%) | 18.m/7000r/min | |||
| The minimum fuel consumption rate is less than g/Kw. h | 354g/KW.h | |||
登录
