YX250-CTR
LB425PTR
一、specification | ||||
English item | specification | |||
Overall dimension (length × wide × Height) mm | 2000mm x 750 mm x 1115mm | |||
Wheelbase mm | 1380 mm | |||
Minimum ground clearance mm | 195mm | |||
Seat cushion height mm | 760 mm | |||
Operating handle return angle (left/right) | ≤35° | |||
Minimum turning radius mm | 520mm | |||
Final transmission ratio | 13:39 | |||
Climbing slope | ≥22° | |||
Seats | 2 | |||
Shift mode | Manual labor | |||
Fuel tank volume L | 14 | |||
Fuel type | 92# | |||
Rated maximum load kg | 150 | |||
Net weight kg | 160 | |||
Curb weight Kg | 165 | |||
Maximum load total kg | 315 | |||
Maximum speed Km/h | 105 | |||
Braking performance m | ≤7m/30km/h | |||
Starting performance S | ≤15S | |||
Rated power Kw/r/min | ||||
Economic fuel consumption L/100Km | 2.8 | |||
Brake | front | Left and right hydraulic disc brake | ||
rear | Hydraulic disc brake | |||
Brake operation | front | Hand brake | ||
rear | foot brake | |||
wheel | Spoke wheel | |||
spoke wheel size | front:3.0×17 rear :4.0×17 | |||
tyre | Inclined rubber | |||
tyre size | 110/60 - 17、130/70 - 17/140/70 - 17 | |||
Tyre pressure (front/rear) Kpa | 200/225 | |||
Specification and illumination of large bulb | 12V 10w (far) /5w (near) | |||
Steering bulb specification | 12V-2W | |||
Battery specification | GTX9-BS/ Semi-maintenance-free battery /150*87*105/ with electrolyte | |||
二、 ENGINE SPECIFICATION | ||||
Engine type | Four-stroke, air-cooled, single-cylinder, vertical | |||
Magneto type | Flywheel rotor type, 12V 8 pole full wave | |||
Stroke mm | 65 | |||
Cylinder diameter mm | 70 | |||
Working volume of cylinder ml | 250.1 | |||
Compression ratio | 9.2:1 | |||
Fuel grade | 93 # gasoline | |||
Total oil capacity L | 1.3 | |||
Spark plug model | D8RTC | |||
Spark plug gap mm | 0.6~0.7 | |||
Valve clearance mm | 0.05±0.02mm | |||
Starting mode | Electric start/kick start | |||
Lubricating oil grade | 15W/40 | |||
Lubrication method | Splash pressure lubrication | |||
Ignition mode | C.D.I | |||
Carburetor model | PZ32 | |||
Carburetor type | Horizontal suction plunger type | |||
Transmission type | Constant mesh two-stage transmission and five-speed transmission | |||
Clutch type | Multi-disc oil bath manual clutch | |||
Primary gear ratio | 3.333 | |||
Gearshift ratio | i1=2.769 ,i2=1.882.i3=1.400,i4=1.130,i5=0.960 | |||
Output transmission mode | Chain drive | |||
Rotation direction of output shaft | Face the output shaft and rotate counterclockwise | |||
Overall dimension (length × wide × Height) mm | 330×318×390 | |||
Net mass Kg | 35±1 | |||
Magneto ignition advance angle | 10º±1º | |||
Rated power and corresponding speed kW (r/min ± 5%) | ||||
Maximum net power and corresponding speed kW (r/min ± 5%) | 12.5N.m/6500r/min | |||
Maximum torque and corresponding speed N.m (r/min ± 5%) | 16.2N.m/6500r/min | |||
The minimum fuel consumption rate is less than g/Kw. h | 367g/KW.h |
登录